Neilsen Logo

CT4007

Spline Bit - M10 x 800mm

Extra-Long Spline Socket Bit
M10 x 800mm 1/2in.Dr
S2 Steel Bit with Chrome Vanadium Socket
For VAG Drive Shaft Bolts
Applicable to Audi / VW vehicles

M10 x 800mm Spline Socket Bit

CT4008

Spline Bit - M12 x 800mm

Extra-Long Spline Socket Bit
M12 x 800mm 1/2in.Dr
S2 Steel Bit with Chrome Vanadium Socket
For VAG Drive Shaft Bolts
Applicable to Audi / VW vehicles

M12 x 800mm Spline Socket Bit

CT4009

Spline Bit - M14 x 800mm

Extra-Long Spline Socket Bit
M14 x 800mm 1/2in.Dr
S2 Steel Bit with Chrome Vanadium Socket
For VAG Drive Shaft Bolts
Applicable to Audi / VW vehicles

M14 x 800mm Spline Socket Bit

CT6058

Pipe Plug Socket Set - 11pc

11pc 3/8in.Dr Pipe Plug Socket Set
Male : 3/16 | 1/4 | 9/32 | 5/16 | 11/32 | 3/8in.
Female : 1/4 | 9/32 | 5/16 | 11/32 | 3/8in.
Tapered Male Square Drive and
Chamfered Female Square Drive aligns socket to fastener quickly
Low profile design provides easy access to tight spaces
Fits any 3/8in.Dr ratchets, bars etc.
Chrome-Molybdenum for high torque impact tools.

Pipe Plug Socket Set

CT4232

VAG Axle Socket Set - 6pc

6pc VAG Axle Nut Socket Set
Includes 14mm and 17mm Hex Bits
M18 Spline Bit and 24 | 30 | 32mm 12-Point Sockets.
1/2in. and 3/4in. Drive
Covers most 1996-2015 VW / Audi Front and Rear Axle Nuts.

VAG Axle Nut Socket Set

CT2544

Socket / Bit Set - 8pc

8pc Drive Shaft Socket Set
Socket and Bit Set Specific for Drive Shafts / Propshafts
1/2in.Dr Hex Bits : 14 | 17 | 19mm
1/2in.Dr Deep Sockets : 27 | 30 | 32 | 34 | 36mm
Chrome-Molybdenum Steel

Driveshaft Socket and Bit Set

CT2997

CV Boot Clamp Pliers

CV Boot Clamp Pliers - 2pc Set
Crimps and flattens ear type Clamps
CV Clamp Banding Tool
For installing CV Clamps
Standard banding tool for CV Joint Boots

CV Boot Clamp Pliers - 2pc Set

CT3023

CV Joint Boot Clamp Pliers

CV Joint Boot Clamp Pliers - Ear Type
Ideal for installing Clamps on fuel filters - water pumps - CV joint boots and other cooling system hoses

CV Joint Boot Clamp Pliers

CT3909

CV Joint Boot Clamp Pliers

CV Drive Shaft Boot Clamp Pliers
For Oetiker CV Drive Shaft boot Securing clips.
3/8in.Dr holes in the handle shafts to enable
a torque Wrench to be used with the tool when required.

CV Drive Shaft Boot Clamp Pliers

CT6425

CV Joint Boot Clamp Pliers

Offset CV Joint Boot Clamp Pliers
Special Boot Clamp Crimping Pliers designed to work in confined spaces
allows you to work on large size boot clamps / top plate on pliers flatten the crimp.
The pliers work from the side - head is turned 90 degrees
unlike traditional tools that work from the end.
Use on eared clamps and Perma-Quick type clamps
used on fuel filters / cooling systems and vacuum lines.
Length : 245mm
Max. Clamping Width : 31mm

CV Joint Boot Clamp Pliers

CT3908

CV Joint Boot Clamp Tool

CV Joint Boot Clamp Tool
For the assembly of Stainless Steel Bands
3/8in.Dr Jaws for use with a Torque Wrench
For torque sensitive rubber boot Clamps

CV Joint Boot Clamp Tool

CT5217

CV Joint Spring Ring Pliers

CV Joint Spring Ring Pliers
This tool is specifically designed to aid the secure removal
and re-installation of the CV Joint Spring Ring without damage.
With Unique jaws for holding the ring securely.
Length : 150mm
Jaw Capacity : 50mm

CV Joint Spring Ring Pliers

CT5124

CV Boot Installation Tool

CV Boot Tool
For installing vehicle rubber CV boots without dismantling the CV joint.
Steel Centre / Plastic Composite Cone.
Diameter Size : 100mm Ex / 93mm Int.
Length : 405mm

CV Boot Installation Tool

CT4887

CV Boot Installation Tool - Pneumatic

Air Powered CV Boot Installation Tool
For the fast and efficient installation of uni-fit boots on the CV joint.
With air control switch to adjust fingers to the size of boot required.
Easily place the boot into place over CV joint.
The boot should be lubricated before each use.
Working pressure : 72-130psi
Air Inlet : 1/4in.

CV Boot Installation Tool

CT2613

CV Boot Installation Tool - Pneumatic

Air Powered Boot Installation Tool for CV Joints
Professional tool for commercial or occasional use.
Used for stretching flexible rubber CV boots
onto automatic drive shaft assemblies
Range : 20 - 110mm Diameter
Installs CV boots without removing axle.
Composite body with simple control valve.
For cars / small vans and light commercial vehicles.
1/4in. BSP inlet

Pneumatic CV Boot Installation Tool

CT4807

Land Rover Prop Shaft Socket

Land Rover Prop Shaft Socket
9/16in. | 3/8in.Dr | 150mm Long
Suitable for
Defender : 90 | 110
Discovery : 1 | 2
Range Rover : P38

Land Rover Prop Shaft Socket

CT5819

Drive Shaft Tool - BMW

BMW Drive Shaft Tool
Suitable for 4 Wheel Drive Vehicles
For removing the drive shaft from the front axle.
Makes disassembly much easier.
OEM Code : 315110

BMW Drive Shaft Tool

CT5490

Inner Drive Shaft Extractor Fork

Inner Drive Shaft Extractor Fork
Designed to engage between the inner drive shaft
and the gearbox housing to lever out the drive shaft.
Total length : 400mm
Jaw width : 82mm
Required on Ford / Mazda / Volvo / Renault / Dacia
and other front wheel drive vehicles.

Inner Drive Shaft Extractor Fork

CT6382

Inner Drive Shaft Extractor Fork

Inner Drive Shaft Extractor Fork
for Ford / Volvo / Renault / Mazda etc.
Contact Lever Diameter : 55mm.
Jaw Diameter : 85mm.
Length : 380mm.
Designed to allow for the quick and safe removal of drive shafts
by connecting properly with the locking clip rings found on many
front wheel drive vehicles preventing damage to the
drive shaft and surrounding components.

Inner Drive Shaft Extractor Fork

CT6381

Lever Set for Auromotive Use

2pc Lever Set
Ideal for clutch and transmission work - also
separating ball joint connections on shifter cables & shift linkages.
Plus axle components / ball joint connection points / exhaust hangers
silent blocks / bushes and many panel types and stuck components
Large Lever / Internal dimensions : 25 x 110mm.
Small Lever / Internal dimensions : 15 x 65mm

Lever Set for Auromotive Use

CT5903

Inner CV Joint Puller

Inner CV Joint Puller
Includes Slide Hammer and 48mm CV Joint Fork.
For removing the axle assembly from the transaxle without
causing damage to aluminium transmission cases or roller bearings.
For most Ford vehicles and other car manufactures.

Inner CV Joint Puller

CT2546

Drive Shaft Puller Set

7pc Drive Shaft Puller Set
230mm Long Puller with 120mm Housing
For BMW and VW Drive Shaft servicing

Drive Shaft Puller Set

CT3384

Propshaft Separator

Adjustable Propshaft Separator
Will fit most makes and models of vehicles - except Seat.

Propshaft Separator

CT3915

Seal Puller

Adjustable Seal Puller
with 2 Hook Shapes
With rotating head for removing various oil and grease seals

Adjustable Seal Puller

CT3684

Seal Puller Set

3pc Seal Puller Set
Suitable for the safe damage free removal of Drive or Transmission Oil and Grease seals or O-rings.
Tool head shape provides better access than other seal pullers.

Seal Puller Set

CT2545

Gear Box Socket Set - 5pc

5pc 1/2in.Dr Castellated Socket Set - Mercedes
Gearbox / differential flange / front axles and bearings / rear axle drive flange
6 / 8mm Tooth x 70 / 80mm Long
For Mercedes G Class -
W-107 / 114 / 115 / 116 / 123 / 126 / 460 / 461 / 463
Chrome Molybdenum

Mercedes Axle and Gear Box Socket Set

CT4806

Gear Box Socket Set - 5pc

5pc 1/2in.Dr Castellated Socket Set - Mercedes
Gearbox / differential flange / front axles and bearings / rear axle drive flange
6 / 8mm Tooth x 70 / 80mm Long
For Mercedes G Class -
W-107 / 114 / 115 / 116 / 123 / 126 / 460 / 461 / 463
Chrome Molybdenum

Mercedes Axle and Gear Box Socket Set

CT5629

Differential Nut Socket

72mm Differential Nut Socket
For loosening or tightening the castellated differential nut
used on the Mercedes-Benz Citaro and Evo Buses.
Castellated 6 Tooth Socket : 11 x 6 x 12mm deep Teeth
Outside Diameter : 84mm | Inside Diameter : 72mm.
Depth : 60mm with 32mm Hex drive.

Mercedes Bus Differential Nut Socket

CT5628

Axle Groove Nut Socket

Mercedes Rear Axle Groove Nut Socket
For 6 teeth groove nuts on low-floor buses with SF portal axle AV132 -
Mercedes-Benz Citaro Bus / MAN City-Line / Neoplan / Kassbohrer
and other vehicles with identical axle.
Designed for high tightening and release torque values.
by hand or impact wrench operation.
Drive tube diameter : 35 mm

Rear Axle Groove Nut Socket

CT5622

Axle Lock Nut Socket - MAN / TGA

MAN / TGA Front Axle Lock Nut Socket
3/4in.Dr / 60mm Hex Drive.
Inner diameter : 134mm
Outer diameter : 147mm
Lug diameter : 118mm / width 11mm
Applicable to Man / TGA Front Axle / V982l-01

Front Axle Lock Nut Socket

CT6410

Differential Flange / Insert Nut Tool Set

BMW Differential Flange / Insert Nut Tool Set
For removing and installing of the drive shaft nut.
Allows inserting of the rear differential pinion seal.
Suitable for BMW vehicles with rear and four wheel drive.
HAG 215 Sp / HAG 220kom / HAG 225kom / HAG type G
Open End Spanner - 50mm
Flange Holding Tool
Multi-Point Ring Spanner - 65mm
Multi-Point Socket - 34T
Seal Ring Drift

Differential Flange / Insert Nut Tool Set

CT4527

Seal Remover Set - 4pc

4pc Spoon Tip Seal Remover Set
with rounded tip and blended edge
for the removal of seals and O-rings
without damage to seal or surface.
2 x Spoon Tips
2 x Contoured Tips
For Seals / Dust Boots / O-rings / Hoses.

Spoon Tip Seal Remover Set
NEILSEN
cannon
Job Site